A range of modern, decorative, pre-primed face, MR MDF panels for interior applications.

Australia.

Surround by Laminex can only be installed in interior applications. The pre-primed panels (face only) can be installed onto prepared plasterboard, timber, steel, brick or masonry wall surfaces.

No. The pre-primed panel face can be finished with your chosen paint colour to enhance your décor.

Batten 25 | Classic VJ 100 | Demi Round 20 (limited stock) | Demi Round 40 | French Stripe 30 | Scallop 45 | Scallop 135.

All decorative MR E0 MDF panels are available in two sizes: 2400mm X 1200mm and 3000mm X 1200mm.

All decorative Fire Resistant Panels (FR E1 MDF) are available in only 3000mm X 1200mm.

All profiles are 12mm thick except Classic VJ 100 which is 9mm thick.

All profiles come with a low pressure melamine back except Classic VJ 100 which has a raw back.

Yes, Surround by Laminex can be used in Internal Moisture Areas such as bathrooms, laundries and kitchens. However, additional preparation, sealing & painting required. Surround by Laminex is prohibited for use in Splash Zones. Refer to section 6.9 of the Fabrication & Installation Manual for detailed instructions.

Surround by Laminex is NOT suitable for areas where the moisture content is likely to be elevated for prolonged periods, such as saunas, indoor swimming pools or industrial wet areas.

Surround by Laminex Fire Resistant panels (FR E1 MDF) are PROHIBITED for use in Internal Moisture Areas.

Yes, as long as it cannot come into contact with liquid / water. When installing around a kitchen island, a toe kick is recommended.

Yes, Surround by Laminex can be installed in a Horizontal Orientation on walls. Refer to section 6.7 of the Fabrication and Installation Manual for detailed instructions.

Yes, as long as all safety standards and clearance rules are adhered to. For more detailed information, section 6.10  of the Fabrication & Installation Manual.

Consult with a professional heating appliance specialist on any building code and regulatory requirements.

All MR E0 MDF decors are Group 3 Fire Rated.

Surround by Laminex is NOT suitable for cabinetry making. It can however be used as a decorative feature, around a fixture such as a shop counter. When installing around a shop counter island, a toe kick is recommended.

Surround by Laminex is NOT suitable for any ceiling or floor applications.

Surround by Laminex is NOT suitable for use in any exterior applications.

Yes, refer to the Fabrication and Installation Manual for instructions.

Tpically you will need the following:

•    Tape measure
•    Spirit level / laser level
•    String line or equivalent
•    Hand saw or circular saw
•    Hammer and or nail gun or screw gun
•    Pencil or chalk for marking out
•    Caulking gun
•    Sanding sponge
•    Recommended adhesives
•    Nails / screws
•    10mm Spacers or off cuts
•    Compatible timber based filler

Sheets are easily attached together using the smart tongue and groove system.

Some trimming maybe required to fit to height and width of area.

Surround by Laminex is made from Medium Density Fibreboard (MDF). MDF responds to the humidity and temperature of the surrounding environment, affecting the moisture content of the product, resulting in panel dimensional change.

Pre-conditioning of Surround by Laminex panels is required in order to achieve moisture content equilibrium (MCE) before fixing, to reduce the likelihood of bowing or shrinkage after installation. Therefore, Surround by Laminex panels must be stored for a minimum period of 48 hours at the same environmental conditions as the subsequent place of use. Failure to condition material may result in product expansion and contraction in response to environmental conditions, particularly with changes in temperature and humidity. This may result in, but is not limited to, bowing or warping of panels, joint failure or build-up of internal stresses that release in the form of cracks.

Not without allowing for panel expansion. Claims arising from peaking, movement or any failure of sheets in place due to the use of butt joins will not be covered under warranty.

Akzo Nobel - High Cover Vacuum Primer (880439013).

It depends on your desired finish preference. Lightly sand all surfaces to be coated to obtain a smooth and even finish. Use a sanding sponge or progressively use finer grit sandpaper to achieve a smooth edge free of damage, racks, dents or notches. Care must be taken not to abrade the decorative routed areas as this may result in permanent damage of the surface to be painted. Damage to Surround by Laminex panels as a result of surface or panel preparation activities will not be recognised under warranty. Use a soft brush to remove all sanding / processing dust and contamination before painting commences.